The Ultra-Spill Deck Standard Model was initially developed to comply with EPA regulations regarding litre capacity, resulting in spill containment products with considerable height. Even today, many pallets remain relatively tall, ranging approximately from 304 to 355 millimetres for 4-drum models and 406 to 431 millimetres for 2-drum models. Although this height may not pose an issue in situations where drums are seldom moved, it becomes problematic in applications requiring frequent movement.
Moreover, taller spill pallets can raise the top of the drum to a potentially hazardous height, especially when handling dangerous materials, increasing the risk of splashes or spills reaching eye level. The Ultra-Spill Deck Standard Model effectively addresses these concerns with its low profile of just 146mm, facilitating easier handling and reducing the risk by keeping drum tops at a safer distance from eye level during hazmat pouring or dispensing.
Benefit from the industry’s most robust warranty, offering five years of protection against any defects in material or workmanship. Learn more.
Product Code | Description | Length (mm) | Width (mm) | Height (mm) | Weight Capacity (kg) | Containment Capacity (L) | Weight (kg) |
CHU1321 | 1-Drum Spill Deck | 657 | 657 | 146 | 680 | 41 | 9 |
CHU1086 | 2-Drum Spill Deck | 1321 | 657 | 146 | 1361 | 83 | 18 |
CHU1072 | 4-Drum Spill Deck | 1321 | 1321 | 146 | 2722 | 167 | 32 |
Product Code | Description | Length (mm) | Width (mm) | Height (mm) | Weight Capacity (kg) | Weight (kg) |
CHU1089 | Loading Ramp for 2-Drum and 4-Drum | 812 | 609 | 146 | 272 | 8 |
CHU1073 | Bulkhead Fitting | 63 | 63 | 63 | N/A | 0.5 |
CHU1131 | 660mm T-Strip | 660 | 38 | 38 | N/A | 0.5 |
CHU2221 | Sidewall Plug | 76 | 76 | 76 | N/A | 0.5 |
We recommend using a pump (Product CHU2345 can be used) to remove any spilled contents from the sump. (Note: spillage should be pumped into an approved container).
The Ultra-Spill Deck Ramp (Product CHU1089) comes complete with two steel clips that quickly install on the end of the ramp. These clips hook onto the connecting spill deck and keep the ramp from moving or shifting during loading or unloading.
NOTE: Product CHU1089 is NOT fluorinated.
NOTE: The ramp is not designed to be used with the 1-Drum Spill Decks or the short side of the 2-Drum Spill Decks.
Other than the spill deck, you’ll need one bulkhead fitting ( Product CHU1473) and one t-strip (Product CHU1431) for every 660mm of spill deck length that is connected. For example, if you’re connecting a 4-drum spill deck to another 4-drum spill deck you would need two bulkhead fittings and two t-strips. If, on the other hand, you were connecting a 1-drum spill deck to the short end of a 2-drum spill deck, you would only need one each of the bulkhead fitting and t-strip.
Yes. All that is required is a 39mm hole saw (31mm will also work). On each side of the Ultra-Spill Decks are “dimpled” areas that indicate where holes are to be drilled. Center the hole saw in the area you need to be drilled and carefully cut the hole(s) for your bulkhead fittings. File or “flame” any rough or sharp edges prior to connecting
Sidewall plugs (Product CHU2221) can be used if you are no longer connecting a spill deck and therefore have a hole that needs to be plugged.
The spill deck can NOT be moved with a forklift or pallet jack. The design of the spill deck sidewalls sometimes leads users to think that it is forkliftable or able to be moved with a pallet jack. But what may appear to be forklift pockets are actually supports for the grating.
Yes, all grating surfaces on the spill decks are slip-resistant.
The t-strips lay across the point where two spill decks come together. By “bridging the gap” this piece diverts spills to either of the decks and keeps any spillage from getting between the units.
One bulkhead fitting and one t-strip for each 660mm of spill deck that is being connected.
(Note: The answer to this question is based on one assumption: That the spill decks are being used with 205L drums). By themselves, the 1-drum, 2-drum and 4-drum spill decks do not meet EPA requirements. They must be connected to a bladder or another Ultra-Spill Deck to increase the total sump capacity to 205 litres minimum.
All spill decks use a grating that is 1219mmL x 609mmW x 63mmH or 609mmL x 609mmW x 63mmH.
Master Distributor of :
Looking for product information? Want to discuss your fabrication requirements? Need a quote?
