The Ultra-Spill Deck Bladder System offers a solution to achieving EPA spill containment compliance with the lowest profile spill containment pallet on the market, without expanding its footprint. This innovation introduces the Ultra-Spill Deck Bladder Systems, enhancing the popular Ultra-Spill Decks by integrating a rolled-up 250 litres bladder. This addition allows any spill deck, whether for 1, 2, or 4 drums, to become self-contained and meet the spill containment regulations.
Benefit from the industry’s most robust warranty, offering five years of protection against any defects in material or workmanship. Learn more.
Product Code | Description | Length (mm) | Width (mm) | Height (mm) | Weight Capacity (kg) | Containment Capacity (L) | Product Weight (kg) |
CHUT1320 | 1-Drum Bladder System | 774 | 657 | 146 | 680 | W/ Bladder: 291 | 12 |
CHUT2329 | 2-Drum Bladder System | 1320 | 774 | 146 | 1361 | W/ Bladder: 333 | 20 |
CHUT2330 | 4-Drum Bladder System | 1438 | 1321 | 146 | 2722 | W/ Bladder: 416 | 30 |
Product Code | Description | Length (mm) | Width (mm) | Height (mm) | Weight Capacity (kg) | Containment Capacity (L) | Product Weight (kg) |
CHUT2317 | Bladder Attachment | 657 | 117 | 117 | N/A | 250 | 2 |
CHUT6340 | Replacement Bladder – For P/N 2317 | 1676 | 1663 | 114 | N/A | 250 | .9 |
CHUT2345 | Bladder Pump | 304 | 177 | 139 | N/A | N/A | 1 |
CHUT1089 | Loading Ramp for 2 & 4-Drums | 812 | 609 | 146 | 272 | N/A | 8 |
No. Spilled liquids will more than likely cause the internal surfaces of the bladder to adhere to each other. We cannot guarantee the proper deployment of a reused bladder.
We recommend using a pump (Product CHUT2345 can be used) to remove any spilled contents from the sump. (Note: spillage should be pumped into an approved container
The spill deck ramp ( Product CHUT1089) comes complete with two steel clips that quickly install on the end of the ramp. These clips hook onto the connecting spill deck and keep the ramp from moving or shifting during loading or unloading. NOTE: The ramp is not designed to be used with the 1-Drum spill decks or the short side of the 2-Drum spill decks.
Other than the spill deck, you’ll need one bulkhead fitting (Product CHUT1073) and one t-strip (Product CHUT1131) for every 660mm of spill deck length that is connected. For example, if you’re connecting a 4-drum spill deck to another 4-drum spill deck you would need two bulkhead fittings and two t-strips. If, on the other hand, you were connecting a 1-drum spill deck to the short end of a 2-drum spill deck, you would only need one each of the bulkhead fitting and t-strip.
Yes. All that is required is a 39mm hole saw (31mm will also work). On each side of the Ultra-Spill Decks are “dimpled” areas that indicate where holes are to be drilled. Center the hole saw in the area you need to be drilled and carefully cut the hole(s) for your bulkhead fittings. File or “flame” any rough or sharp edges prior to connecting.
Sidewall plugs ( Product CHUT2221) can be used if you are no longer connecting a spill deck and therefore have a hole that needs to be plugged.
Yes, all grating surfaces on the spill decks are slip-resistant.
The spill deck can NOT be moved with a forklift or pallet jack. The design of the spill deck sidewalls sometimes leads users to think that it is forkliftable or able to be moved with a pallet jack. But what may appear to be forklift pockets are actually supports for the grating.
The t-strips lay across the point where two spill decks come together. By “bridging the gap” this piece diverts spills to either of the decks and keeps any spillage from getting between the units.
(Note: The answer to this question is based on one assumption: That the spill decks are being used with 205 litre drums). By themselves, the 1-drum, 2-drum, and 4-drum spill decks do not meet EPA requirements. They must be connected to a bladder or another Ultra-Spill Deck to increase the total sump capacity to 230 litres minimum.
Ultra-Spill Deck Plus Models use a grating that is 1320mmL x 660mmW x 101mmH. All other spill decks use a grating that is 1219mmL x 609mmW x 63mmH.
The replacement bladder (Product CHUT6340) is what you would need to order. It is just the bladder and does not include the outer housing. The bladder attachment (Product CHUT2317) includes a bladder and the outside housing.
The bladder will roll out 1663mm away from the deck and will be 1,676mm wide when completely unfurled.
The bladder(s) should be replaced for any of the following reasons: (1) It captures a spill (regardless of the size of the spill), (2) It deploys, rolls, or falls out of the bladder attachment housing. (3) It has sat unused for more than five years.
MASTER DISTRIBUTOR OF:
Looking for product information? Want to discuss your fabrication requirements? Need a quote?
